Link: DorsEast-PP         Site: Exarro
System Status
Attributes Value Units Attributes Value Units
CMU Wireless Link
MAC Address
header=[MAC Address] body=[Unit MAC address]>
00:04:56:30:2a:5a
  Wireless Link Status
header=[Wireless Link Status] body=[Current status of the wireless link. A state of 'Up' on a green background indicates that a PTP link is established]>
Up
 
Software Version
header=[Software Version] body=[Current software version]>
800-05-02
  Link Loss
header=[Link Loss] body=[Link Loss is a measurement of the loss in signal level as the radio wave propagates between the antennas installed at each end of the link. The Link Loss is only accurate if the Antenna Gain and RF Feeder Loss have been configured correctly at both ends of the link. The statistics are provided for the most recent hour of operation, or less if the System Histograms have been reset within the hour.
INSERTHIST]>
 145.0,
 144.7,
 144.5,
 145.0
dB 
Hardware Version
header=[Hardware Version] body=[Hardware platform version]>
06.06-FIPS
  Channel Separation
header=[Channel Separation] body=[Radio license channel separation]>
28 MHz 
Elapsed Time Indicator
header=[Elapsed Time Indicator] body=[Elapsed time since the last system reboot]>
7 Days 09:33:35
hh:mm:ss  Wireless Transmitter
RFU Maximum Transmit Power
header=[Maximum Transmit Power] body=[Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link. Note that when an IRFU is connected rather than an ODU, the transmit power refers to the power at the transceiver output and not the IRFU antenna port. See the User Guide for more details]>
22.0
dBm 
RFU Status
header=[RFU Status] body=[Current status of the RFU. A state of 'OK' on a green background indicates that the RFU is fully operational, although may not be transmitting.]>
OK
  Transmit Power
header=[Transmit Power] body=[This is the transmit power of the RFU. When an IRFU transceiver is connected rather than an ODU the Transmit Power refers to the power at the transceiver output and not the IRFU antenna port. The statistics are provided for the most recent hour of operation, or less if the System Histograms have been reset within the hour.
INSERTHIST]>
 22.0,
 22.0,
 22.0,
 22.0
dBm 
Transmitter Status
header=[Transmitter Status] body=[Indicates whether the RFU is transmitting or muted. In a 1+1 Hot Standby configuration, it will also indicate if the RFU is Inactive and therefore ready to transmit.]>
Transmitting
  Transmit Link Capacity
header=[Transmit Link Capacity] body=[The maximum data capacity available for user traffic in the Transmit direction under the current radio link conditions, irrespective of Ethernet rate limitations. The displayed Transmit data rates may be lower than this figure if the link isn't fully loaded by the current traffic profile]>
151.12
Mbps 
RFU Type
header=[RFU Type] body=[RFU type as: RFU platform, frequency band, Tx-Rx frequency spacing, Hi/Lo band and transmit frequency range]>
ODU-A 7GHz TR196 Lo 7093-7149MHz   Transmit Capacity Limit
header=[Transmit Capacity Limit] body=[Transmit capacity is limited by the lower of:
1) the capacity limit specified by the installed License Key
2) the Ethernet speed negotiated at the other end of the wireless link.]>
Unlimited
 
RFU Serial
header=[RFU Serial] body=[RFU serial number]>
218KPG2188
  Transmit Capacity Limit Detail
header=[Transmit Capacity Limit Detail] body=[A brief description of the reason (if any) for the limit being applied to the transmit capacity]>
Running At Unlimited Capacity
 
RFU Version Bank 2
header=[RFU Version Bank 2] body=[RFU firmware version number (nnn/ddMMYY) in bank 2]>
106/160410
  Transmit Modulation Mode
header=[Transmit Modulation Mode] body=[Current active transmit modulation mode]>
128QAM 0.84  
Remote Identification Transmit Modulation Selection Detail
header=[Transmit Modulation Selection Detail] body=[This indicates how the current ACM modulation was determined]>
Limited By Wireless Conditions
 
Remote Site Name
header=[Remote Site Name] body=[This field is allocated by the system administrator and contains a description of the site name together with any additional notes]>
Valkop
  Wireless Receiver
Remote IP Address
header=[Remote IP Address] body=[IP Address of the peer wireless unit]>
http://41.57.39.14   Receive Power
header=[Receive Power] body=[This is the receive power measured by the RFU. When an IRFU transceiver is connected rather than an ODU, the Receive Power refers to the power at the input to the transceiver and not the IRFU antenna port. The statistics are provided for the most recent hour of operation, or less if the System Histograms have been reset within the hour.
INSERTHIST]>
 -55.0,
 -55.2,
 -55.5,
 -55.5
dBm 
Ethernet Vector Error
header=[Vector Error] body=[Vector Error is a measure of received signal quality. The value is generally in the range from -6 dB to -38 dB, a more negative number indicating a higher quality signal. The statistics are provided for the most recent hour of operation, or less if the System Histograms have been reset within the hour.
INSERTHIST]>
 -24.8,
 -26.2,
 -27.0,
 -26.3
dB 
Data Port Status
header=[Data Port Status] body=[Current status of the data Ethernet link. A state of 'Up' on a green background indicates that an Ethernet link is established. A state of 'Down' on a red background indicates that an Ethernet link is not established]>
Copper Link Up
  Receive Link Capacity
header=[Receive Link Capacity] body=[Maximum capacity provided by the wireless link in the receive direction. This depends on the Channel Bandwidth and the Modulation Mode being used by the receiver. The received data rate may not achieve the wireless capacity if the License Key installed at the other end of the wireless link restricts its transmit capacity limit or if the Ethernet Port at either end of the wireless link has negotiated a speed which is lower than the wireless capacity]>
125.33
Mbps 
Data Port Speed And Duplex
header=[Data Port Speed And Duplex] body=[The current speed and duplex of the data Ethernet link]>
1000 Mbps Full Duplex
  Receive Modulation Mode
header=[Receive Modulation Mode] body=[Current active receive modulation mode]>
64QAM 0.82